Isolierstöße ÖBB 07.09.26
|
insulated rail joint
|
Technical delivery conditions for track / requirements for track components
|
AA-E 004 (TVFA)
|
Strain measurement by means of strain gauges
|
|
AASHTO LRFD
|
AASHTO LRFD Brigde Construction Specification (3. Edition)
|
|
ASTM A 262
|
Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
|
|
ASTM A 370
|
Standard Test Methods and Definitions for Mechanical Testing of Steel Products
|
|
ASTM A 923
|
Standard Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels
|
|
ASTM E 112
|
Standard Test Methods for Determining Average Grain Size
|
|
ASTM E 562
|
Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count
|
|
ASTM G 28
|
Standard Test Methods for Detecting Susceptibility to Intergranular Corrosion in Wrought, Nickel-Rich, Chromium-Bearing Alloys
|
|
ASTM G 48
|
Standard Test Methods for Pitting and Crevice Corrosion Resistance of Stainless Steels and Related Alloys by Use of Ferric Chloride Solution
|
|
CIP
|
Cable Stays, Recommendations of French interministerial commission on Prestressing Chapter
|
|
DIN 50100
|
Load controlled fatigue testing - Execution and evaluation of cyclic tests at constant load amplitudes on metallic specimens and components
|
|
DIN 50159-1
|
Metallic materials - Hardness testing with the UCI method - Part 1: Test method
|
|
DIN 51214
|
Testing of Steel - Tensile test for round wires using knotted specimens
|
|
DSB 80
|
Conditions concerning the manufacture and use of steel wire ropes for cableway installations with passenger conveyance, Section 30, 3rd edition, published by the Federal Ministry of Public Economy and Transport
|
|
EAD 160004-00-0301
|
Post-tensioning kits for prestressing of structures
|
|
EAD 160027-00-0301
|
Special filling products for post tensioning kits
|
|
EN 10218-1
|
Steel wire and wire products - General - Part 1: Test methods
|
|
EN 10244-2
|
Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2
|
|
EN 12385-1
|
Steel wire ropes - Safety - Part 1: General requirements
|
|
EN 12797
|
Brazing - Destructive tests of brazed joints
|
|
EN 12927-8
|
Safety requirements for cableway installations designed to carry persons - Ropes -part 8: Nondestructive testing
|
|
EN 13146-1
|
Railway applications - Track - Test methods for fastening systems - Part 1: Determination of longitudinal rail restraint
|
|
EN 13146-2
|
Railway applications - Track - Test methods for fastening systems - Part 2: Determination of torsional resistance
|
|
EN 13146-3
|
Railway applications - Track - Test methods for fastening systems - Part 3: Determination of attenuation of impact loads
|
|
EN 13146-4
|
Railway applications - Track - Test methods for fastening systems - Part 4: Effect of repeated loading
|
|
EN 13146-5
|
Railway applications - Track - Test methods for fastening systems - Part 5: Determination of electrical resistance
|
|
EN 13146-6
|
Railway applications - Track - Test methods for fastening systems - Part 6: Effect of severe environmental conditions
|
|
EN 13146-7
|
Railway applications - Track - Test methods for fastening systems - Part 7: Determination of clamping force and uplift stiffness
|
|
EN 13146-9
|
Railway applications - Track - Test methods for fastening systems - Part 9: Determination of stiffness
|
|
EN 13230-1
|
Railway applications - Track - Concrete sleepers and bearers - Part 1: General requirements
|
|
EN 13230-2
|
Railway applications - Track - Concrete sleepers and bearers - Part 2: Prestressed monoblock sleepers
|
|
EN 13230-3
|
Railway applications - Track - Concrete sleepers and bearers - Part 3: Twin-block reinforced sleepers
|
|
EN 13230-4
|
Railway applications - Track - Concrete sleepers and bearers - Part 4: Prestressed bearers for switches and crossings
|
|
EN 13230-5
|
Railway applications - Track - Concrete sleepers and bearers - Part 5: Special elements
|
|
EN 13481-2
|
Railway applications - Track - Performance requirements for fastening systems - Part 2: Fastening systems for concrete sleepers
|
|
EN 13481-3
|
Railway applications - Track - Performance requirements for fastening systems - Part 3: Fastening systems for wood sleepers
|
|
EN 13481-4
|
Railway applications - Track - Performane requirements for fastening systems - Part 4: Fastening systems for steel sleepers
|
|
EN 13481-5
|
Railway applications - Track - Performance requirements for fastening systems - Part 5: Fastening systems for slab track with rail on the surface or rail embedded in a channel
|
|
EN 13481-7
|
Railway applications - Track - Performance requirements for fastening systems - Part 7: Special fastening systems for switches and crossings and check rails
|
|
EN 13481-8
|
Railway applications - Track - Performance requirements for fastening systems - Part 8: Fastening systems for track with heavy axle loads
|
|
EN 13796-2
|
Safety requirements for cableway installations designed to carry persons - Carriers - Part 2: Slipping resistance tests for grips
|
|
EN 13796-3
|
Safety requirements for cableway installations designed to carry persons - Carriers - Part 3: Fatigue testing
|
|
EN 14587-1
|
Railway applications - Infrastructure - Flash butt welding of new rails - Part 1: R220, R260, R260Mn, R320Cr, R350HT, R350LHT, R370CrHT and R400HT grade rails in a fixed plant
|
|
EN 14587-2
|
Railway applications - Track - Flash butt welding of rails - Part 2: New R220, R260, R260Mn and R350HT grade rails by mobile welding machines at sites other than a fixed plant
|
|
EN 14587-3
|
Railway applications - Track - Flash butt welding of rails - Part 3: Welding in association with crossing construction
|
|
EN 14730-1
|
Railway applications - Track - Aluminothermic welding of rails - Part 1: Approval of welding processes
|
|
EN 1537
|
Execution of special geotechnical works - Ground anchors
|
|
EN 50182
|
Conductors for overhead lines - Round wire concentric lay stranded conductors
|
|
EN 61395
|
Overhead electrical conductors - Creep test procedures for stranded conductors
|
|
EN ISO 10447
|
Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds
|
|
EN ISO 14270
|
Resistance welding - Destructive testing of welds - Specimen dimensions and procedure for mechanized peel testing resistance spot, seam and embossed projection welds
|
|
EN ISO 14271
|
Resistance welding - Vickers hardness testing (low-force and microhardness) of resistance spot, projection, and seam welds
|
|
EN ISO 14272
|
Resistance welding - Destructive testing of welds - Specimen dimensions and procedure for cross tension testing of resistance spot and embossed projection welds
|
|
EN ISO 14555
|
Welding - Arc stud welding of metallic materials
|
|
EN ISO 1460
|
Metallic coatings - Hot dip galvanized coatings on ferrous materials - Gravimetric determination of the mass per unit area
|
|
EN ISO 148-1
|
Metallic materials - Charpy pendulum impact test - Part 1: Test method
|
|
EN ISO 15630-1
|
Steel for the reinforcement and prestressing of concrete - Test methods - Part 1: Reinforcing bars, rods and wire
|
|
EN ISO 15630-2
|
Steel for the reinforcement and prestressing of concrete - Test methods - Part 2: Welded fabric and lattice girders
|
|
EN ISO 15630-3
|
Steel for the reinforcement and prestressing of concrete - Test methods - Part 3: Prestressing steel
|
|
EN ISO 17639
|
Destructive tests on welds in metallic materials - Macroscopic and microscopic examination of welds
|
|
EN ISO 17653
|
Resistance welding - Destructive tests on welds in metallic materials - Torsion test of resistance spot welds
|
|
EN ISO 17660-1
|
Welding - Welding of reinforcing steel - Part 1: Load-bearing welded joints
|
|
EN ISO 2307
|
Fibre ropes - Determination of certain physical and mechanical properties
|
|
EN ISO 2639
|
Steels - Determination and verification of the depth of carburized and hardened cases
|
|
EN ISO 3651-1
|
Determination of resistance to intergranular corrosion of stainless steels - Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)
|
|
EN ISO 3651-2
|
Determination of resistance to intergranular corrosion of stainless steels - Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels - Corrosion test in nitric acid medium by measurement of loss in mass (Huey test)
|
|
EN 13749
|
Railway applications. Wheelsets and bogies. Method of specifying the structural requirements of bogie frames
|
|
EN 13796-3:2005
|
Safety requirements for cableway installations designed to carry persons. Carriers. Fatigue tests
|
|
fip bulletin 30
|
Acceptance of stay cable systems using prestressing steel
|
|
ISO 1099
|
Metallic materials. Fatigue testing. Axial force-controlled method
|
|
ISO 15835-2:2009
|
Steels for the reinforcement of concrete. Reinforcement couplers for mechanical splices of bars. Test methods
|
|
UIC 515-4
|
Passenger rolling stock - trailer bogies - running gear - bogie running gear - bogie frame structure strength tests
|
|
UIC 615-4
|
Motive power units bogies and running gear bogie frame structure tests
|
|